in-lite

12/2 Low Voltage Landscape Wire Quick shop
12/2 Low Voltage Landscape Wire
In-Lite

12/2 Low Voltage Landscape Wire

$160.00 $180.00

12/2 Landscape x 75M (250') designed for the in-lite and Hadco landscape lighting connectors.
View product
ACE DOWN Quick shop

in-lite

ACE DOWN

$125.00 $139.00

ACE DOWN
ACE DOWN
ACE DOWN
in-lite

ACE DOWN

$125.00 $139.00

The ACE DOWN wall-mounted light fixture produces a targeted beam of light and can be mounted on a wall or fence. Since the LED light source is placed deep inside the fixture, the light is not blinding. The ACE DOWN is available in two colors: Rosé Silver and Dark Gray. 12V 

View product
ACE UP DOWN Quick shop

in-lite

ACE UP DOWN

$131.00 $199.00

ACE UP DOWN
ACE UP DOWN
ACE UP DOWN
ACE UP DOWN
in-lite

ACE UP DOWN

$131.00 $199.00

The ACE UP-DOWN 100-230V wall-mounted fixture can only be connected to a 120V power supply. This makes it suitable for use on the outdoor wall of a home, garage or shed. The two LED light sources direct a light beam upwards and downwards. The ACE UP-DOWN 100-230V is available in two colors: Rosé Silver and Dark Gray.

PRODUCT DETAILS

Dimensions: 
103x100x100mm (lxwxh)
Material: 
Aluminium casing and polycarbonate lens
Color: 
Rosé Silver or Dark Gray
Light source: 
LED
Lighting intensity: 
Large
Voltage: 
100V - 240V
Capacity: 
8,5W
Illumination angle: 
66º
Light reach: 
3,5 m (11,5 ft)
View product
Ace Up/ Down 12V Quick shop

in-lite

Ace Up/ Down 12V

$125.00 $135.00

Ace Up/ Down 12V
in-lite

Ace Up/ Down 12V

$125.00 $135.00

The ACE UP-DOWN wall fixture provides a focused beam of light both upwards and downwards. The fixture is suitable for use on a fence or wall. The two light sources lie deep within the fixture to ensure the light is not blinding. Do you prefer a narrower beam or a softer light? The separately available ACE accessories allow you to personalize the light bundles from the ACE fixtures to suit your taste and situation. 

Dimensions:

Length
95 mm
3.74 in
Width
64 mm
2.52 in
Height
120 mm
4.72 in

Materials & finish:

Color
White, Black, Silver
Housing
Aluminum
Lens
Polycarbonate

Technical specifications:

Voltage
Power
6,50W
Electric potential
10,30VA
Light source
LED
Burn time
25000
Light type
Direct
Light angle
63°
Light distribution
12ft
Light color
Warm white
Lighting direction
Downwards
Upwards
Color temperature
3000K
CRI
92
Dimmable
No
IP class
IP-55
Energy label
A
View product
BIG SCOPE Quick shop

in-lite

BIG SCOPE

$129.00 $145.00

BIG SCOPE
BIG SCOPE
BIG SCOPE
BIG SCOPE
in-lite

BIG SCOPE

$129.00 $145.00

High Power 7 WATT LED

Spotlight in charcoal grey coated aluminium finished with a stylish anodised aluminium ring. Provides an atmospheric beam of light. Ground stake included, base plate available separately. The SCOPE and BIG SCOPE shine equally far. However, the beam of light of the BIG SCOPE is twice as wide.

Dimensions Ø 65 mm (2.4 inches)
Material Aluminium housing / glass lens
Colour Charcoal grey
Power 12V/7W
Light reach 5 metres (16.4 feet)
Use Accent lighting for special features in the garden such as trees, shrubs, statues and exterior walls.
Installation

Mounting in soft surfaces with supplied ground stake or on hard surface with the separately-available base plate.

 

5 Year Warranty

Connector Included

View product
BLINK Quick shop

in-lite

BLINK

$99.00

BLINK
in-lite

BLINK

$99.00

Round wall-mounted fixture in warm silver-coated aluminum. Comes with two lenses: transparent and matte. For a focused or, indeed, dispersed Warm White light.

12V- Low Voltage

LED

Rose Silver

View product
BLINK BRONZE Quick shop
BLINK BRONZE
in-lite

BLINK BRONZE

$99.00

Round wall-mounted fixture in new bronze aluminum. Comes with two lenses: transparent and matte. For a focused or, indeed, dispersed Warm White light.

12V- Low Voltage

2W LED

Bronze Finish

View product
Concrete Kit for HYVE Lights Quick shop
Concrete Kit for HYVE Lights
Concrete Kit for HYVE Lights
Concrete Kit for HYVE Lights
Concrete Kit for HYVE Lights
Concrete Kit for HYVE Lights
Concrete Kit for HYVE Lights
in-lite

Concrete Kit for HYVE Lights

$550.00 $678.00

This starter rough in kit includes (10) pre cut sleeves of 2 1/2" x 14" with shaved sleeve so no wider ring on the Hyve is required, meaning a sleeker look! It also includes (320') of 1/2 flexible core-line, (250') of 12/2 Landscape Wire, a (1) 56W transformer, (20) 1/2" coreline connectors and (1) roll of duct tape and (1) Hyve (ww) light to test and rough in during install. 

Simply place pre cut sleeves for every light/HYVE product you plan on installing throughout your concrete area.   

Next from your low voltage transformer run core-line to first sleeve  placed in light location, cut core-line and place under cut pipe location or cut out two 1/2" holes to place connectors and fasten coreline for a secure placement. 

Next run new core-line from sleeve as per above and run to the next sleeve which is the next light location.  Continue this till you reach your final light location.

Once core-line runs are roughed in, now you can run your landscape wire.  Push wire in from transformer location and follow core-line.  Landscape wire is ran throughout each pipe location running continuously in every core-line to final light location.   Be sure to pull lots of extra wire at the end as in the next step we will go though the step of leaving extra wire (looped) in each sleeve.

Once wire is ran throughout, now go to each sleeve starting from the last and first and pull back extra wire so each pipe has at least 18" of looped wire inside so later on there is enough to connect the lights in every sleeve.

Once given enough slack of wire in each pipe, again 14" of looped wire suggested in each pipe.  Now you can fasten the sleeves to the rebar and place duct tape over and under the pipe to ensure no concrete is poured into the pipe.  Remember the lights and wire need to fit in the cut pipe locations so duct tape will ensure concrete does not enter.

Concrete is poured and dried, great now is the fun part!  

Sleeves may be lower or higher then the concrete and thats okay.  If pipe is higher than the poured concrete simply peel back the top portion of the duct tape and cut back the sleeve so its flush with the concrete ensuring not to cut the wire!

If sleeve is lower, its okay the light (hyve) sits on the concrete so its ready for light install.

Connecting and installing the HYVE lights.  The kit comes with (1) HYVE (ww) light.

The HYVE light comes with a speciality connector, simply peel pack the duct tape as per above step if not done already, grab your slack of wire and connect the wire to the connector.  Once connected attached light to connector.  

Final step, place small portion of silicon under ring and place light in sleeve, pushing in the wire, connector and light so it fits all in the pipe.

Power on transformer to test lights, if any lights are not on, check connection on wire for that light and ensure the connector was tightened and not loosened when pushing light in. 

View product
Concrete Sleeves kit for Hyve Lights Quick shop
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
Concrete Sleeves kit for Hyve Lights
in-lite

Concrete Sleeves kit for Hyve Lights

$1,430.00 $1,590.00

This newly added kit includes (10) pre cut sleeves of 2 1/2" x 14" with shaved sleeve so no wider ring on the Hyve is required, a sleeker look! It also includes (320') of 1/2 flexible core-line, (250') of 12/2 Landscape Wire, a (1) 108W transformer and the (10) HYVE (ww) lights, (20) 1/2" coreline connectors and (1) roll of duct tape.

Simply place pre cut sleeves for every light/HYVE product you plan on installing throughout your concrete area.   

Next from your low voltage transformer run core-line to first sleeve  placed in light location, cut core-line and place under cut pipe location or cut out two 1/2" holes to place connectors and fasten coreline for a secure placement. 

Next run new core-line from sleeve as per above and run to the next sleeve which is the next light location.  Continue this till you reach your final light location.

Once core-line runs are roughed in, now you can run your landscape wire.  Push wire in from transformer location and follow core-line.  Landscape wire is ran throughout each pipe location running continuously in every core-line to final light location.   Be sure to pull lots of extra wire at the end as in the next step we will go though the step of leaving extra wire (looped) in each sleeve.

Once wire is ran throughout, now go to each sleeve starting from the last and first and pull back extra wire so each pipe has at least 18" of looped wire inside so later on there is enough to connect the lights in every sleeve.

Once given enough slack of wire in each pipe, again 14" of looped wire suggested in each pipe.  Now you can fasten the sleeves to the rebar and place duct tape over and under the pipe to ensure no concrete is poured into the pipe.  Remember the lights and wire need to fit in the cut pipe locations so duct tape will ensure concrete does not enter.

Concrete is poured and dried, great now is the fun part!  

Sleeves may be lower or higher then the concrete and thats okay.  If pipe is higher than the poured concrete simply peel back the top portion of the duct tape and cut back the sleeve so its flush with the concrete ensuring not to cut the wire!

If sleeve is lower, its okay the light (hyve) sits on the concrete so its ready for light install.

Connecting and installing the HYVE lights.  The kit comes with (10) HYVE lights ( more can be purchased separately) as kits only comes with (10).

The HYVE lights comes with a speciality connector, simply peel pack the duct tape as per above step if not done already, grab your slack of wire and connect the wire to the connector.  Once connected attached light to connector.  

Final step, place small portion of silicon under ring and place light in sleeve, pushing in the wire, connector and light so it fits all in the pipe.

Power on transformer to test lights, if any lights are not on, check connection on wire for that light and ensure the connector was tightened and not loosened when pushing light in. 

View product
EVO- evolution in landscape lighting Quick shop
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
EVO- evolution in landscape lighting
in-lite

EVO- evolution in landscape lighting

$82.50 $105.00

Our new exclusive EVO collection, which contains six fixtures, features the latest and very best LED's - a true evolution in light. This means the fixtures are very energy-efficient and help to create very natural colors in your garden. In addition, the fixtures feature a ‘diamond cut’ lens which ensures effective and uniform light distribution. Combine products from the EVO range and transform your outdoor space into somewhere you enjoy spending time during the day and in the evening.

Integrated: EVO GROUND 300 DARK

The EVO GROUND 300 DARK allows us to introduce multi-functional integrated line-lighting with a streamlined, architectonic design. The fixture features a casing made from hard anodized aluminum, which gives it a stylish appearance. The EVO GROUND 300 DARK is perfect for decoratively lighting paths, driveways and hedges, and is simple to incorporate into paving, gravel and lawns. You can thus create superb lighting effects in no time at all.

Solitary: EVO DARK & EVO LOW DARK

The EVO DARK & EVO LOW DARK are real eye-catchers. These standalone fixtures provide a lot of light, but are certainly not blinding. They are thus ideal for decoratively lighting paths and driveways.

Wall: EVO DOWN DARK

The stylish EVO DOWN DARK wall lamp is perfect for decoratively lighting walls, fences and brickwork. It serves as a design object during the day and, in the evening, creates a pleasant lighting effect without blinding you. 

Surface: EVO HYDE 180 DARK & EVO HYDE 550 DARK

The EVO series also allows us to introduce a new product group featuring indirect line-lighting: SURFACE. The EVO HYDE 180 DARK & EVO HYDE 550 DARK allow you to easily create new lighting effects in your garden. For example, they can be incorporated into staircases, platforms, balustrades, benches and pond elements.

The exclusive EVO range will be available from the end of April 2018.

View product
Extensions for Landscape Lighting Quick shop
Extensions for Landscape Lighting
in-lite

Extensions for Landscape Lighting

$10.00

Extension cord type 18/2 length available 1M, 2M & 3 meters (10 ft). Used to increase the distance between the fixture and the low voltage cable. Can also be used to increase the distance between the light sensor and the transformer.

View product
FLUX Family Quick shop
FLUX Family
FLUX Family
FLUX Family
FLUX Family
FLUX Family
FLUX Family
in-lite

FLUX Family

$99.00

Flux

Renewed for the 2015 season! The FLUX 60 LED ground spot is finished with a stylish stainless steel ring and emits a beam of Warm White light. Because the ring rests on the surface it is also easy to embed this ground spot into wood, for example. For illuminating special features in the yard such as trees, shrubs, statues and exterior walls. 

Stainless Steel Ring

2 Watt

12V- Low Voltage

Integrated accent lighting for special features in the yard such as shrubs, statues and exterior walls.

Big Flux

The BIG FLUX is ideal for illuminating high, wide trees which, for example, have been incorporated into decking or for illuminating wide facades from the ground.

  • Produces a strong and focused light
  • Designed for illuminating tall elements up to 7½ meters
  • Drive-over
Installation advice:

A BIG FLUX every 2 to 2½ meters

BIG FLUX NARROW

The BIG FLUX NARROW ground light is ideal for illuminating narrow, high objects.

  • Produces a strong and narrow, focused light
  • Designed for illuminating tall elements up to 11 meters
  • Drive-over
Installation advice:

A BIG FLUX NARROW every 2 to 2½ meters

View product
Fusion Quick shop

In-Lite

Fusion

$90.00

Fusion
Fusion
Fusion
Fusion
In-Lite

Fusion

$90.00

The soft glow of the FUSION LED ground light allows you to subtly illuminate, for example, your deck or driveway.

  • Produces a soft light that does not glare
  • Designed for illuminating a walkway or deck
  • Drive-over
Installation advice:

A FUSION every 1 to 1½ meters


View product
HYVE Quick shop

in-lite

HYVE

$90.00 $109.00

HYVE
HYVE
HYVE
HYVE
HYVE
in-lite

HYVE

$90.00 $109.00

Subtle round fixture finished with a wide stainless steel ring. The lens honeycomb structure creates warm atmospheric lightning.

12V- Low Voltage

1W LED

Stainless Steel

View product
HYVE 22 RVS Warm White Quick shop
HYVE 22 RVS Warm White
HYVE 22 RVS Warm White
HYVE 22 RVS Warm White
in-lite

HYVE 22 RVS Warm White

$45.00

This subtle fixture with a diameter of 22 mm is fitted with a stainless steel ring. In the evening, it produces an attractive warm light that, thanks to the lens with honeycomb structure, does not blind. This makes this fixture suitable for stairs and terraces, for example. The HYVE 22 with stainless steel goes together well with the other fixtures in the HYVE line.

PRODUCT DETAILS

Dimensions: 
Ø 22 mm, ring Ø 28 mm, overall height 55 mm
Material: 
Impact-resistant polycarbonate, filled with a two-component resin, stainless steel ring
Color: 
Silver stainless steel
Light source: 
LED
Lighting intensity: 
Small
Voltage: 
12V
Capacity: 
0.25W
Light reach: 
0.5 (2 ft)

USE: 

Concrete Natural stone Wood
Lawn Drive-over
View product